 |
Built-in 255-step sequential signal source
|
|
Voltage/Current output for four quadrants
|
|
High power : ±60V (Can be shifted)
BP4610 : ±10A (30Ap-p)
BP4612 : ±20A (60Ap-p)
|
|
Wide band: DC to 150kHz (CV)
|
|
Constant voltage (CV) / Constant current (CC) operation selectable
|
|
Response calibration function
|
|
Voltage/Current limiter, measurement display
function
|
|
USB interface and external analogue input
|
|
Available for Sequence Editing Software (BP0421E optional) |
|
Enriched
Basic Performance
|
|
|
|
| Fully
equipped specification providing high voltage, high current,
high speed, and constant current operation. |
| High voltage required in testing
12V/24V/42V vehicle electrical and electronic components,
high current necessary for large parts, high speed required
in driving actuators, and furthermore, constant current
operation effective in driving solenoids with low impedance.
With enriched specfication satisfying all such requirements,
BP series responds to the needs in developement of devices
and device testing. |
 |
| |
BP4610 |
BP4620 |
| High
output voltage |
120Vp-p
Output range can be shifted to -5 V to +115
V and -115 V to +5 V, depending on limiter
setting |
| High
current |
±10A
(DC)
30Ap-p
|
±20A
(DC)
60Ap-p |
| Wide
band |
DC to 150kHz |
| Operation
mode |
Constant voltage
(CV) / Constant current (CC) operation selectable |
|
|
|
Wide-Ranging
Output Area
|
|
|
|
| Bipolar
power source capable of handling positive/negative voltage
and sink/source current |
| BP series can output
in four quadrants and is capable of handling two directions
of current, which are source (supply) and sink (absorption)
current, let alone positive/ negative voltage. From devices
that generate back electromotive force such as solenoids,
capacitive load such as electrolytic capacitor, and even
to piezoelectric material charged with electromotive force
and power sources and batteries such as fuel cells, you
can connect BP4610 to devices and systems that cannot
be driven with normal DC power supply with a sense of
security. |
 |
•This
is an example with outpu of voltage ±60V.
•>Depending on the limiter
setting, the output voltage can be shifted to -5V to +115V
and -115V to +5V (Output current range changes when the
ouput range shifts.)
•The number 1 to 4 stands
for the quadrant nnumber. |
|
Universal
Output Pattern
|
|
|
|
| Built-in
sequential signal source that allows you to use sweep
and arbitrary waveform |
BP series
has a built-in sequential signal source. For example,
by programming a series of voltage change pattern used
in voltage fluctuation test on electrical and electronic
components, the test can be done in a single operation
since the output changes in order according to the procedure.
When setting a sequence, you can use DC (direct current),
sine wave, and square wave provided in the system and
arbitrary waveform (16 types) loaded via USB interface.
Maximum of 255 steps (minimum 0.1 ms per step) can be
set and waveform, level, duration, and continuous/sweep
can be selected for each step. Furthermore, you can specify
repetition of sequence for 1 to 999 times (or continuous).
In addition, the power supply provides branch operation
in which the external trigger input moves the sequence
to a specified step, the function to stop the sequence,
and the function to hold the operation. |
|
| Various
Output Patterns Using Sequence Functions |
Relay Operation
Test
(Withstand Power Supply
Fluctuation Test) |
 |
Vehicle
Electrical and Electronic Components Test
(ISO/DIS7637-2.2 Pulse 4)
(Simulation of Transient
Voltage Drops at Startup) |
 |
|
|
|
|
 |
|
|
|
Optimum
Response for Each Load
|
|
|
|
| Response
calibration function |
| BP series has a new response calibration
function that allows users to individually optimize transient
response characteristic in square wave output or sudden
output change. Transient response for load with complicated
impedance characteristic such as electromagnetic components
with inductance (coil component) or capacitance (capacitor
component) differs among loads. BP series has a new and
convenient response calibration function with which users
can adjust response characteristic according to the load. |
 |
 |
 |
| Before
Calibration |
|
After
Calibration |
|
|
Attentive
Additional Functions
|
|
|
|
 |
Voltage/Current limiter effective
in preventing load failure
|
|
AC/DC voltage/current measurement
display for monitoring output state
|
|
USB interface easily connectable with PC
|
|
External analogue input that can be used even
for oscillators and record signal
|
|
Output ON/OFF function, monitor output, store/recall
memory, external control input/output, and key lock |
|
Worldwide-compatible power input of
90 V to 250 V (BP4610) |
|
