japanesechinese


NF Corporation
network contact us site map
Google  
home about nf products support news
Measurement Instruments Power Supply and Power Control produts Function Modules Customized Products
home > Products > Measurement Instruments > LCR Meter > ZM2371/ZM2372/ZM2376 > Peripheral Equipment
Product Information

LCR Meter
LCR Meter
ZM2371/ZM2372/ZM2376

Test Fixtures and Leads (sold separately)
Accurate and easy-to-perform measurements
A variety of measurement fixtures are available for various applications.
*Measurement frequency range is the recommended measurement range with  consideration of an error.

General-purpose components
dot
Test leads provide 4-terminal measurements. Accurate measurement is possible to low impedance. Kelvin clip leads enable one clip to be used for two electrically insulated opposing electrodes.


2324   Four-terminal alligator-clip test leads
Use these test leads with low-impedance four-terminal components, including those which have separate current supply terminals and voltage test terminals.
ZM2391 Three-terminal alligator-clip test leads
A three-terminal type is also available for simpler measurements.
Measurement frequency: ≤ 100 kHz
dot

2325AL
2325A (L/M)   Kelvin clip test leads
The two test lead clips enable four-terminal connections. The 2325A can be used to test large or unusually shaped components that cannot be easily inserted into the direct test fixture. Select between two types: the standard L type or the M type with smaller clips.
Measurement frequency: ≤ 100 kHz

[M type]

[L type]
dot
ZM2392   Kelvin clip test leads
The ZM2392 provides test leads for simpler measurements.
Measurement frequency: ≤ 20 kHz
dot
ZM2391   Three-terminal alligator-clip test leads
A three-terminal type is also available for simpler measurements.
Measurement frequency: ≤ 20 kHz
top of this page


Lead components
dot

ZM2363   Test fixture
Test fixture that makes 4-terminal measurements as easy as inserting the leads into the sample.
To match the size of the components, the spacing of the measurement terminals can be adjusted.
Measurement frequency: ≤ 10 MHz




Chip components (Test Fixture)
dot
Test fixture for measuring surface-mounted components with a 2-terminal connection. Since a cable is not used, stray capacitance and residual impedance are small, enabling accurate open and short correction.

ZM2394   Chip test fixture
Measurement frequency: ≤ 2 MHz
Supported component size: 0603[JIS] / 0201 [EIA] (0.3mm thick) to 14 mm (square)
dot
ZM2394H   Chip test fixture
Measurement frequency: ≤ 30 MHz
Supported component size: 0603[JIS] / 0201 [EIA] (0.3mm thick) to 14 mm (square)
dot
ZM2393
ZM2393   Chip test fixture
Measurement frequency: ≤ 1.2 MHz
Supported component size: 
1608 [JIS] / 0603 [EIA] to 5750 [JIS] / 2220 [EIA]
top of this page


Chip components (Test Leads)
dot
Chip component test lead in a 3-terminal configuration with shielded measurement contacts.
Stray capacitance is small, enabling easy measurement of small-capacity capacitors.

2326A   Chip component test leads
Measurement frequency: ≤ 1.2 MHz
Tip spacing: 0.5 to 8 mm (typ.)



Adapter

DC bias voltage adapter
dot
Adapter for applying a DC bias voltage of ±40 V to the sample. This adapter provides easy connection to the LCR meter and test fixture. (4-terminal pair configuration)
ZM2328 ZM2328
ZM2328 (For ZM2371 and ZM2372) ZM2329 (For ZM2376)


back
top of this page